Offshore Drilling

Drilling for natural gas offshore, in some instances hundreds of miles away from the nearest landmass, poses a number of different challenges over drilling onshore. The actual drilling mechanism used to delve into the sea floor is much the same as can be found on an onshore rig. However, with drilling at sea, the sea floor can sometimes be thousands of feet below sea level. Therefore, while with onshore drilling the ground provides a platform from which to drill, at sea an artificial drilling platform must be constructed.

Source: ChevronTexaco Corporation

Drilling offshore dates back as early as 1869, when one of the first patents was granted to T.F. Rowland for his offshore drilling rig design. This rig was designed to operate in very shallow water, but the anchored four legged tower bears much resemblance to modern offshore rigs. It wasn't until after World War II that the first offshore well, completely out of sight from land, was drilled in the Gulf of Mexico in 1947. Since then, offshore production, particularly in the Gulf of Mexico, has been very successful, with the discovery and delivery of a great number of large oil and gas deposits.

The Drilling Template
Since the land that is going to be drilled through cannot provide a base for offshore drilling as it does for onshore drilling, an artificial platform must be created. This artificial platform can take many forms, depending on the characteristics of the well to be drilled, including how far underwater the drilling target is. One of the most important pieces of equipment for offshore drilling is the subsea drilling template. Essentially, this piece of equipment connects the underwater well site to the drilling platform on the surface of the water. This device, resembling a cookie cutter, consists of an open steel box with multiple holes in it, dependent on the number of wells to be drilled. This drilling template is placed over the well site, usually lowered into the exact position required using satellite and GPS technology. A relatively shallow hole is then dug, in which the drilling template is cemented into place. The drilling template, secured to the sea floor and attached to the drilling platform above with cables, allows for accurate drilling to take place, but allows for the movement of the platform above, which will inevitably be affected by shifting wind and water currents.
In addition to the drilling template, a blowout preventer is installed on the sea floor. This system, much the same as that used in onshore drilling, prevents any oil or gas from seeping out into the water. Above the blowout preventer, a specialized system known as a 'marine riser' extends from the sea floor to the drilling platform above. The marine riser is designed to house the drill bit and drillstring, and yet be flexible enough to deal with the movement of the drilling platform. Strategically placed slip and ball joints in the marine riser allow the subsea well to be unaffected by the pitching and rolling of the drilling platform.
Moveable Offshore Drilling Rigs
There are two basic types of offshore drilling rigs: those that can be moved from place to place, allowing for drilling in multiple locations, and those rigs that are permanently placed. Moveable rigs are often used for exploratory purposes because they are much cheaper to use than permanent platforms. Once large deposits of hydrocarbons have been found, a permanent platform is built to allow their extraction. The sections below describe a number of different types of moveable offshore platforms.

A Drilling Barge

Source: California Department of Transportation

Drilling Barges
Drilling barges are used mostly for inland, shallow water drilling. This typically takes place in lakes, swamps, rivers, and canals. Drilling barges are large, floating platforms, which must be towed by tugboat from location to location. Suitable for still, shallow waters, drilling barges are not able to withstand the water movement experienced in large open water situations.
Jack-Up Rigs

A Jack-Up Rig

Source: National Oceanic and Atmospheric Administration

Jack-up rigs are similar to drilling barges, with one difference. Once a jack-up rig is towed to the drilling site, three or four 'legs' are lowered until they rest on the sea bottom. This allows the working platform to rest above the surface of the water, as opposed to a floating barge. However, jack-up rigs are suitable for shallower waters, as extending these legs down too deeply would be impractical. These rigs are typically safer to operate than drilling barges, as their working platform is elevated above the water level.
Submersible Rigs
Submersible rigs, also suitable for shallow water, are like jack-up rigs in that they come in contact with the ocean or lake floor. These rigs consist of platforms with two hulls positioned on top of one another. The upper hull contains the living quarters for the crew, as well as the actual drilling platform. The lower hull works much like the outer hull in a submarine - when the platform is being moved from one place to another, the lower hull is filled with air - making the entire rig buoyant. When the rig is positioned over the drill site, the air is let out of the lower hull, and the rig submerses to the sea or lake floor. This type of rig has the advantage of mobility in the water, however once again its use is limited to shallow water areas.

A Semisubmersible Rig

Source: Department of the Interior

Semisubmersible Rigs
Semisubmersible rigs are the most common type of offshore drilling rigs, combining the advantages of submersible rigs with the ability to drill in deep water. Semisubmersible rigs work on the same principle as submersible rigs; through the 'inflating' and 'deflating' of its lower hull. The main difference with a semisubmersible rig, however, is that when the air is let out of the lower hull, the rig does not submerge to the sea floor. Instead, the rig is partially submerged, but still floats above the drill site. When drilling, the lower hull, filled with water, provides stability to the rig. Semisubmersible rigs are held in place by huge anchors, each weighing upwards of ten tons. These anchors, combined with the submerged portion of the rig, ensure that the platform is stable and safe enough to be used in turbulent offshore waters. Semisubmersible rigs can be used to drill in much deeper water than the rigs mentioned above.

A Drillship in the Beaufort Sea

Source: Mining and Minerals Service

Drillships
Drillships are exactly as they sound: ships designed to carry out drilling operations. These boats are specially designed to carry drilling platforms out to deep-sea locations. A typical drillship will have, in addition to all of the equipment normally found on a large ocean ship, a drilling platform and derrick located on the middle of its deck. In addition, drillships contain a hole (or 'moonpool'), extending right through the ship down through the hull, which allow for the drill string to extend through the boat, down into the water. Drillships are often used to drill in very deep water, which can often be quite turbulent. Drillships use what is known as 'dynamic positioning' systems. Drillships are equipped with electric motors on the underside of the ships hull, capable of propelling the ship in any direction. These motors are integrated into the ships computer system, which uses satellite positioning technology, in conjunction with sensors located on the drilling template, to ensure that the ship is directly above the drill site at all times.
Offshore Drilling and Production Platforms

An Offshore Platform

Source: Duke Energy Gas Transmission Canada

As mentioned, moveable rigs are commonly used to drill exploratory wells. In some instances, when exploratory wells find commercially viable natural gas or petroleum deposits, it is economical to build a permanent platform from which well completion, extraction, and production can occur. These large, permanent platforms are extremely expensive, however, and generally require large expected hydrocarbon deposits to be economical to construct. Some of the largest offshore platforms are located in the North Sea, where because of almost constant inclement weather, structures able to withstand high winds and large waves are necessary. A typical permanent platform in the North Sea must be able to withstand wind speeds of over 90 knots, and waves over 60 feet high. Correspondingly, these platforms are among the largest structures built by man. There are a number of different types of permanent offshore platforms, each useful for a particular depth range.
This depiction of offshore drilling and completion platforms gives an idea of just how massive these offshore rigs can be. For reference, the fixed platform (the shallowest shown) is usually in no more than 1,500 feet of water - whereas the height of the Hoover Dam, from top to bottom, is less than half that, at just under 730 feet. Because of their size, most permanent offshore rigs are constructed near land, in pieces. As the components of the rig are completed, they are taken out to the drilling location. Sometimes construction or assembly can even take place as the rig is being transported to its intended destination.

Offshore Drilling Platforms

Source: MMS

Fixed Platforms
In certain instances, in shallower water, it is possible to physically attach a platform to the sea floor. This is what is shown above as a fixed platform rig. The 'legs' are constructed with concrete or steel, extending down from the platform, and fixed to the seafloor with piles. With some concrete structures, the weight of the legs and seafloor platform is so great, that they do not have to be physically attached to the seafloor, but instead simply rest on their own mass. There are many possible designs for these fixed, permanent platforms. The main advantages of these types of platforms are their stability, as they are attached to the sea floor there is limited exposure to movement due to wind and water forces. However, these platforms cannot be used in extremely deep water, it simply is not economical to build legs that long.
Compliant Towers
Compliant towers are much like fixed platforms. They consist of a narrow tower, attached to a foundation on the seafloor and extending up to the platform. This tower is flexible, as opposed to the relatively rigid legs of a fixed platform. This flexibility allows it to operate in much deeper water, as it can 'absorb' much of the pressure exerted on it by the wind and sea. Despite its flexibility, the compliant tower system is strong enough to withstand hurricane conditions. To learn more about compliant tower platforms, click here.
Seastar Platforms
Seastar platforms are like miniature tension leg platforms. The platform consists of a floating rig, much like the semisubmersible type discussed above. A lower hull is filled with water when drilling, which increases the stability of the platform against wind and water movement. In addition to this semisubmersible rig, however, Seastar platforms also incorporate the tension leg system employed in larger platforms. Tension legs are long, hollow tendons that extend from the seafloor to the floating platform. These legs are kept under constant tension, and do not allow for any up or down movement of the platform. However, their flexibility does allow for side-to-side motion, which allows the platform to withstand the force of the ocean and wind, without breaking the legs off. Seastar platforms are typically used for smaller deep-water reservoirs, when it is not economical to build a larger platform. They can operate in water depths of up to 3,500 feet. For an example of a Seastar platform in the Gulf of Mexico, click here.

A Floating Production System

Source: Minerals Management Service

Floating Production Systems
Floating production systems are essentially semisubmersible drilling rigs, as discussed above, except that they contain petroleum production equipment, as well as drilling equipment. Ships can also be used as floating production systems. The platforms can be kept in place through large, heavy anchors, or through the dynamic positioning system used by drillships. With a floating production system, once the drilling has been completed, the wellhead is actually attached to the seafloor, instead of up on the platform. The extracted petroleum is transported via risers from this wellhead to the production facilities on the semisubmersible platform. These production systems can operate in water depths of up to 6,000 feet.

A Tension Leg Platform

Source: Minerals Management Service

Tension Leg Platforms
Tension leg platforms are larger versions of the Seastar platform. The long, flexible legs are attached to the seafloor, and run up to the platform itself. As with the Seastar platform, these legs allow for significant side to side movement (up to 20 feet), with little vertical movement. Tension leg platforms can operate as deep as 7,000 feet.
Subsea System
Subsea production systems are wells located on the sea floor, as opposed to at the surface. Like in a floating production system, the petroleum is extracted at the seafloor, and then can be 'tied-back' to an already existing production platform. The well can be drilled by a moveable rig, and instead of building a production platform for that well, the extracted oil and natural gas can be transported by riser or even undersea pipeline to a nearby production platform. This allows one strategically placed production platform to service many wells over a reasonably large area. Subsea systems are typically in use at depths of 7,000 feet or more, and do not have the ability to drill, only to extract and transport.


Source

NaturalGas.org

Rotary Drilling

Rotary drilling uses a sharp, rotating drill bit to dig down through the Earth's crust. Much like a common hand held drill, the spinning of the drill bit allows for penetration of even the hardest rock. The idea of using a rotary drill bit is not new. In fact, archeological records show that as early as 3000 B.C., the Egyptians may have been using a similar technique. Leonardo Da Vinci, as early as 1500, developed a design for a rotary drilling mechanism that bears much resemblance to technology used today. Despite these precursors, rotary drilling did not rise in use or popularity until the early 1900's. Although rotary drilling techniques had been patented as early as 1833, most of these early attempts at rotary drilling consisted of little more than a mule, attached to a drilling device, walking in a circle! It was the success of the efforts of Captain Anthony Lucas and Patillo Higgins in drilling their 1901 'Spindletop' well in Texas that catapulted rotary drilling to the forefront of petroleum drilling technology.
While the concept for rotary drilling - using a sharp, spinning drill bit to delve into rock - is quite simple, the actual mechanics of modern rigs are quite complicated. In addition, technology advances so rapidly that new innovations are being introduced constantly. The basic rotary drilling system consists of four groups of components. The prime movers, hoisting equipment, rotating equipment, and circulating equipment all combine to make rotary drilling possible.
Prime Movers
The prime movers in a rotary drilling rig are those pieces of equipment that provide the power to the entire rig. Up until World War II, rotary rigs were traditionally powered by steam engines. Diesel engines became the norm after the war. Recently, while diesel engines still compose the majority of power sources on rotary rigs, other types of engines are also in use. Natural gas or gasoline engines are commonly used, as are natural gas or gasoline powered reciprocating turbines, which generate electricity on site. The resulting electricity is used to power the rig itself. Other rotary rigs may use electricity directly from power lines. Most rotary rigs these days require 1,000 to 3,000 horsepower, while shallow drilling rigs may require as little as 500 horsepower. Rotary rigs designed to drill in excess of 20,000 feet below surface may require much more than 3,000 horsepower. The energy from these prime movers is used to power the rotary equipment, the hoisting equipment, and the circulating equipment, as well as incidental lighting, water, and compression requirements not associated directly with drilling.

Working on an Onshore Drilling Rig

Source: Anadarko Petroleum Corporation

Hoisting Equipment
The hoisting equipment on a rotary rig consists of the tools used to raise and lower whatever other equipment may go into or come out of the well. The most visible part of the hoisting equipment is the derrick, the tall tower-like structure that extends vertically from the well hole. This structure serves as a support for the cables (drilling lines) and pulleys (draw works) that serve to lower or raise the equipment in the well. For instance, in rotary drilling, the wells are dug with long strings of pipe (drillpipe) extending from the surface down to the drill bit. If a drill bit needs to be changed, either due to wear and tear or a change in the subsurface rock, the whole string of pipe must be raised to the surface. In deep wells, the combined weight of the drillpipe, drill bit, and drill collars (thicker drillpipe located just above the bit) may be in excess of thousands of pounds. The hoisting equipment is used to raise all of this equipment to the surface so that the drill bit may be replaced, at which point the entire chain of drillpipe is lowered back into the well.

Positioning the Hoisting Equipment

Source: Anadarko Petroleum Corporation

The height of a rigs derrick can often be a clue as to the depth of the well being dug. Drillpipe traditionally comes in 30ft sections, which are joined together as the well is dug deeper and deeper. This means that even if a well is 20,000 feet deep, the drill string must still be taken out in 30 foot sections. However, if the derrick is tall enough, multiple joints of drillpipe may be removed at once, speeding up the process a great deal. Rotating Equipment
The rotating equipment on a rotary drilling rig consists of the components that actually serve to rotate the drill bit, which in turn digs the hole deeper and deeper into the ground. The rotating equipment consists of a number of different parts, all of which contribute to transferring power from the prime mover to the drill bit itself. The prime mover supplies power to the rotary, which is the device that turns the drillpipe, which in turn is attached to the drill bit. A component called the swivel, which is attached to the hoisting equipment, carries the entire weight of the drillstring, but allows it to rotate freely.
The drillpipe (which, when joined together, forms the drillstring) consists of 30ft sections of heavy steel pipe. The pipes are threaded so that they can interlock together. Drillpipe is manufactured to meet specifications laid out by the American Petroleum Institute (API), which allows for a certain degree of homogeneity for drillpipes across the industry. The drillpipe is a very heavy, strong pipe, but can be quite flexible when used in slant or horizontal drilling applications.
Below the drillpipe are drill collars, which are heavier, thicker, and stronger than normal drillpipe. The drill collars help to add weight to the drillstring, right above the bit, to ensure there is enough downward pressure to allow the bit to drill through hard rock. The number and nature of the drill collars on any particular rotary rig can be altered depending on the down hole conditions experienced while drilling.

Diamond Studded Drill Bits

Source: Sandia National Laboratory (left), DOE - National Energy Technology Laboratory

The drill bit is located at the bottom end of the drillstring, and is responsible for actually making contact with the subsurface layers, and drilling through them. The drill bit is responsible for breaking up and dislodging rock, sediment, and anything else that may be encountered while drilling. There are dozens of different drill bit types, each designed for different subsurface drilling conditions. Different rock layers experienced during drilling may require the use of different drill bits to achieve maximum drilling efficiency. It can be a long process to change bits, due to the fact that the whole drill string must be removed; but using the correct drill bit, or replacing a worn bit, can save a great deal of time during drilling. Drill bits are chosen given the underground formations expected to be encountered, the type of drilling used, whether or not directional drilling is needed, the expected temperatures underneath the Earth, and whether or not cores (for logging purposes) are required. There are four main types of drill bits, each suited for particular conditions.

• Steel Tooth Rotary Bits are the most basic type of drill bit used today.
• Insert Bits are steel tooth bits with tungsten carbide inserts.
• Polycrystalline Diamond Compact Bits have polycrystalline diamond inserts attached to the carbide inserts found in Insert Bits.
• Diamond Bits have industrial diamonds implanted in them, to drill through extremely hard rock formations. Diamond bits are forty to fifty times harder than traditional steel bits, and can thus be used to drill through extremely hard rock without dulling overly quickly.

In addition to these main types of drill bits, hybrid bits, combining the features of various types of bits, can be used. If core samples are required for logging purposes, core bits are designed to drill and obtain these samples. There are a great number of different designs for drill bits, including tricone roller bits, button bits, tapered bits, fishtail bits, and mill bits. Each of these bits has specifically designed drilling traits. The fishtail bit, for instance, is designed to enlarge the drill hole above the drill bit, and the mill bit is designed to mill away metal scraps or objects found in the well. The drill bit, in addition to being very useful, is also very expensive. It is thus up to the drilling engineer to ensure that the correct bit is used at the correct time, to allow for maximum drilling efficiency, with minimum wear and tear on the valuable bit.

Lowering the Bit and Drill Collar into the Well Hole

Source: NGSA

Circulating System
The final component of rotary drilling consists of the circulating system. There are a number of main objectives of this system, including cooling and lubricating the drill bit, controlling well pressure, removing debris and cuttings, and coating the walls of the well with a mud type-cake. The circulating system consists of drilling fluid, which is circulated down through the well hole throughout the drilling process.
Typically, liquid drilling fluids are used. The most common liquid drilling fluid, known as 'mud', may contain clay, chemicals, weighting materials, water, oil, or gases. 'Air drilling' is the practice of using gasses as the drilling fluid, rather than a liquid. Gases used include natural gas, air, or engine exhaust. Air drilling can significantly cut down on drilling time, as well as drilling fluid costs. The drilling fluid, much like the bit, is custom designed and chosen depending on what type of subsurface conditions are expected or experienced. For example, if drilling is occurring through underground salt formations, freshwater would not be used, as this would risk dissolving the subsurface salt. Similarly, if drilling near sources of fresh water, salt water would not be used for fear of contaminating the fresh water.
The drilling fluid chosen must have a number of properties to allow it to accomplish its tasks. It must be light and thin enough to circulate through the drill bit, cooling the bit as it drills as well as lubricating the moving parts. The fluid must be heavy enough to carry drill cuttings away from the bit and back to the surface, as well as control upward pressure that may be experienced in the well to prevent blowouts. The drilling fluid engineer ensures that the weight of the drilling fluid is greater than the upward pressure of escaping gas that may be encountered while drilling. In addition, the drilling fluid must be thick enough to coat the wellbore with a cake, which serves to temporarily seal the walls of the well until casing can be installed.
The circulating system consists of a starting point, the mud pit, where the drilling fluid ingredients are stored. Mixing takes place at the mud mixing hopper, from which the fluid is forced through pumps up to the swivel and down all the way through the drill pipe, emerging through the drill bit itself. From there, the drilling fluid circulates through the bit, picking up debris and drill cuttings, to be circulated back up the well, traveling between the drill string and the walls of the well (also called the 'annular space'). Once reaching the surface, the drilling fluid is filtered to recover the reusable fluid.

An Onshore Drilling Rig

Source: DOE - EREN

In addition to the fluid itself regulating downhole pressures encountered while drilling, a device known as the 'blowout preventer' is situated on the well casing below the deck of the rig. A blowout can occur when uncontrolled underground oil or gas pressure exerts more upward pressure than the drilling fluid itself can offset. The blowout preventer can consist of hydraulically powered devices that can seal off the well quickly and completely, preventing any potential for a well blowout should extreme downhole pressures be encountered. Pressure release systems are also installed to relieve the great pressure that can be experienced in a blowout situation.












Source

NaturalGas.org

Onshore Drilling

Onshore Drilling

Source: ChevronTexaco Corporation Drilling into the Earth in the hopes of uncovering valuable resources is nothing new. In fact, the digging of water and irrigation wells dates back to the beginning of recorded history. At first, these wells were primarily dug by hand, then by crude stone or wood tools. Metallurgy brought about the use of iron and bronze tools to delve beneath the Earth's surface, and innovations led to more efficient ways of removing debris from the newly dug hole. The first recorded instance of the practice of 'drilling' holes in the ground came about around 600 B.C., when the Chinese developed a technique of repeatedly pounding bamboo shoots capped with metal bits into the ground. This crude technology was the first appearance of what is now known as 'percussion drilling'; a method of drilling that is still in use today. Much advancement has been made since these first bamboo drilling implements, with the realization of the value and increased demand for subsurface hydrocarbons. This section will cover the basics of modern onshore natural gas drilling practices. There are two main types of onshore drilling. Percussion, or 'cable tool' drilling, consists of raising and dropping a heavy metal bit into the ground, effectively punching a hole down through the Earth. Cable tool drilling is usually used for shallow, low pressure formations. The second drilling method is known as rotary drilling, and consists of a sharp, rotating metal bit used to drill through the Earth's crust. This type of drilling is used primarily for deeper wells that may be under high downhole pressure. Cable Tool Drilling Cable tool, or percussion drilling is recognized by many as the first drilling method employed to dig wells into the Earth for the purpose of reaching petroleum deposits and water. This method is still in use in some of the shallow wells in the Appalachian Basin, although rotary drilling has taken over the bulk of modern drilling activities. The basic concept for cable tool drilling consists of repeatedly dropping a heavy metal bit into the ground, eventually breaking through rock and punching a hole through to the desired depth. The bit, usually a blunt, chisel shaped instrument, can vary with the type of rock that is being drilled. Water is used in the well hole to combine with all of the drill cuttings, and is periodically bailed out of the well when this 'mud' interferes with the effectiveness of the drill bit. Early Percussion Rigs in Pennsylvania - Late 1800's Source: Office of Fossil Energy, DOE Cable tool drilling has historically taken many forms. In the early days of percussion drilling, equipment was very crude compared to today's technology. The 'springpole' technique, used in the early 1800's, consisted of a flexible pole (usually a tree trunk) anchored at one end, and laying across a fulcrum, much like a diving board. The flexible pole, or springpole, would have a heavy bit attached at the loose end. In order to get the bit to strike the ground, workers would use their own body weight to bend the pole towards the ground, allowing the bit to strike rock. The tension in the pole would spring the bit free, should it become stuck in the ground. Much advancement has been made since these early percussion rigs. In fact, it was from cable tool drilling that one of the most important drilling advancements was made. In 1806, David and Joseph Ruffner were using the springpole technique to drill a well in West Virginia. In order to prevent their well from collapsing, they used hollow tree trunks to reinforce the sides of the well, and to keep water and mud from entering the well as they dug. They are credited as the first drillers to use a casing in their well - an advancement that made drilling much more efficient and easily accomplished. It is believed by many that 'Colonel' Drake's 1856 well achieved success due to the use of steel casing to reinforce the well. Drake's well was drilled using steam powered cable tool drilling methods. A Modern, Mobile Cable Tool Drilling Rig Source: Anadarko Petroleum Corporation Innovations, such as the use of steam power in cable tool drilling, greatly increased the efficiency and range of percussion drilling. Conventional man-powered cable tool rigs were generally used to drill wells 200ft or less, while steam powered cable tool rigs, consisting of the familiar derrick design, had an average drilling depth of 400 to 500 feet. The deepest known well dug with cable tool drilling was completed in 1953, when the New York Natural Gas Corporation drilled a well to a depth of 11,145 ft Source NaturalGas.org.